WWW.PAKLIGHT-SHARING.COM

ASIA & PAKISTAN NO 1 DIGITAL SATELLITE NETWORK FORUM
It is currently May 26th, 2018, 5:31 am

All times are UTC + 5 hours


FULL FAST ALL HD/SD CLINE MGLINE VPS RECHARGE SKRILL/PAYPAL DOLLER AVAILABLE CALL 0301 8331640



PAK TIGER SUPER FAST SERVER CCCAM HD+SD CLINE PANEL,VPS,LOW RATES CALL GULAB 0301 8001309


HD/SD CCCAM SERVER DISHTV+VIDECOIN HD/SD+RELINCE HD/SD+SUNHD/SD+DIALOGE SD/HD PROVIDER CALL ABBAS 0301 833 1640


WE ARE THANKS TO RAMZAN KHOSA/MUDASAR/JOYAHMED/MUDASSARRAJA/MAHDIKHAN/ARIF TO START FREE SERVER IN OUR SITE


ALL 1506F CHINA RACIEVER NEW SOFTWARE 18/05/2018


hollywood top movies trailer watch Now Here



Post new topic Reply to topic  [ 2 posts ] 
Author Message
PostPosted: January 6th, 2016, 11:39 am 
Offline
SITE_FOUNDERâ„¢
SITE_FOUNDERâ„¢
User avatar

Joined: January 19th, 2015, 8:20 am
Posts: 1739
Has thanked: 1398 times
Been thanked: 3356 times


Hi everyone!
As I have received a few PMs about what I do to install MultiCS successfully, I would like to offer my own contribution to successful, simple and fool-proof installation of MultiCS.

First of all, if you have decided that you want to rent a VPS server, choose a good hosting provider! Good providers are those that are the most responsive when you contact them for support. Ask their sales dept.to give you a test IP. Once you have that IP, ping it and see what response you have in your country. If you are happy with the ping reply and the prices, you can buy pretty safely.

Of course, if you want low ECM time, avoid buying cheap USA VPS if you are based in Europe, as your ping will be very high and will indeed impact the quality of viewing you offer to your peers.

Once you are satisfied with your hosting provider, choose a good package. Forget getting a good VPS for just $5, a decent VPS server that will give you a good troublefree experience should have about 2GB RAM and enough CPU power and bandwidth (even better if unlimited!) and is probably going to cost around $15-20/month.

So, you have just received your VPS welcome mail... so, what's next?

1) Install the operating system. My personal recommendation is Ubuntu 12.04. Choose 64bit if your VPS has at least 2GB RAM, 32 bit if less than that.

2) Log in to VPS shell, using the password you have chosen or been given. The first commands you should enter are the following:

apt-get update
apt-get upgrade
This will update and upgrade your system packages to the latest version. You should run both commands about once a week.

3) Install the very handy text editor "nano". It's much simpler to use than "vi" and you install it like this:

apt-get install nano
4) Now, let's start to be security-conscious. First, change the SSH port from the standard port 22 to something "less standard". You do it this way.

nano /etc/ssh/sshd_config
5) in the document you see, scroll down to line 13, where you see "PORT". Change that number to anything you like. Remember that port number!!!!! Save the document in nano by pressing CTRL and X together. Type Y to save the file.

6) Now, it's time to test your newly configured new SSH port. To do that, enter this commands, one after the other:

stop ssh
start ssh
exit
ssh root@yourdyndnshost.com -p XYZ (where XYZ is the port you have chosen to edit at point 5) above
7) Now, it's time to install MultiCS!!!!

Download the release you wish to install (ie. r77) from this site, and unzip it on your desktop. If you have 64bit, you will need "multics.x64", if you have 32bit "multics.x32". Rename the file you need as "multics" only, with NO extension.

8) Using any FTP client (such as FileZilla) create a connection profile of SFTP type (FTP over SSH), using your host as the server, the SSH port chosen at point 5), root as the user and the root password to connect. Navigate to /usr/local/bin and place your multics binary file in there. Still using FileZilla, give it permission 755.

9) Now, still using the FTP client, move to /var/ and create a new directory in there. Call it "etc" and give it permission 755.

10) Now, upload these files into that directory (you should find them easily here on this site):

CCcam.channelinfo, CCcam.prio, CCcam.providers, baddcw.cfg, ip2country.csv, multics.cfg, multics.css, oscam.srvid, sid.list

give all these files permission 755 too.

11) Now, we need to edit our multics.cfg file that comes included in the r77 release.

In particular, we need to pay attention to these areas:

we add a line to the file to use the file baddcw.cfg that we uploaded earlier, in the "FILES" section:

INCLUDE: "/var/etc/baddcw.cfg"

We also make modifications here:

##########################################################
## HTTP SERVER
##########################################################

HTTP PORT: 5500 ## HTTP server listening port, default: 5500.(0=disabled) >>> choose any port number you like and REMEMBER IT!!!

## web user/pass protection
HTTP USER: admin >>> change it to the user name you wish
HTTP PASS: admin >>>> change the password, use a SECURE ONE!!!!

12) Now we are ready to include the profiles we want to share and receive from our peers. So, we need to edit this section here:


#### FIRST PROFILE
[CanalsatHD] # Profile name
------------
CAID: 0100 # Caid
PROVIDERS: 3311,3315,3317 # Providers list
ONID: 31 # Operator Network ID (hex value)
SID LIST: 20D2,20D3,20D4 # Accept ecm requests only for channels from sid list
DENY SIDLIST: YES # Reject request for channels within sidlist (default=NO=accept)
ECM LENGTH: 64 # Accept only request with ecm length = 0x64 (hex)
DCW TIMEOUT : 3500 # delay after that if no cw returned from servers, multics would send decode failed to client
DCW MAXFAILED: 10 # Maximum of successive decode failed returned from a card on a channel to block sending ecm requests to this card
DCW CHECK: 1 # Check and filter wrong dcw for this profile if the client sending request has dcwcheck enabled (default=0)
SERVER MAX: 0 # (dont use) max server to use for decoding one ecm request. (default=0,unlimited)
SERVER FIRST: 2 # the number of servers to send ecm upon receiving request (default=0, one server)
SERVER INTERVAL: 1000 # interval between sending ecm request to servers. first server will be requested at receiving ecm request from client, the second request will be done after "SERVER INTERVAL" has been elapsed and so ...
SERVER TIMEOUT: 2500 # max time for selecting servers to decode one ecm request it must be greater than "SERVER INTERVAL"
SERVER VALIDECMTIME: 2000 # Disable sending ecmrequest to cards with ecmtime greater than 2000ms (default=0,all card are accepted)
RETRY NEWCAMD: 1 # Number of retries for newcamd servers (default=0(no retry);max=3)
RETRY CCCAM: 5 # Number of retries for Cccam servers (default=0;max=10)
DISABLE NEWCAMD: NO # Enable/Disable sending ecm requests to Newcamd servers (default=NO,enabled)
DISABLE CCCAM: NO # Enable/Disable sending ecm requests to CCcam servers (default=NO,enabled)
DISABLE RADEGAST: NO # Enable/Disable sending ecm requests to Radegast servers (default=NO,enabled)
DISABLE CACHE: NO # Enable/Disable receiving dcw from cache (default=NO,enabled)
ENABLE CACHEEX: YES # Enable/Disable receiving dcw from cacheex (default=NO,disabled)
CACHEEX VALIDECMTIME: 1000 # Block sending dcw from local cache to cacheex if they have ecmtime greater than 1000ms
## Newcamd
KEY: 01 02 03 04 05 06 07 08 09 10 11 12 13 14 # newcamd des key (optional, if not set default key is used)
PORT: 5501 # if not set the value of the previous profile's port is taken +1 (default=8000)
# newcamd clients
USER: user1 pass1 # Newcamd client ( nline is like that "N: mydns.dns 5501 user1 pass1 01 02 03 04 05 06 07 08 09 10 11 12 13 14" )
USER: user2 pass2

On this very same site, you find plenty of good profiles, ready to copy and paste. Select A UNIQUE PORT for each profile, usually a range of consecutive ports, such as: 6000, 6001, 6002, and so on.

Once you have finished, it's time to launch MultiCS!!!

13) From SSH shell, enter the following commands:

cd /usr/local/bin
./multics -b
You should see:

Multi CardServer r77 - by evileyes (email:evileyes@live.fr)
Congratulations!!! MultiCS is up and running!!

Now, access the web interface and continue configuring using your web browser, like this:

http://yourdynamichost.com:zzzz
zzz stands for the port you choose for the HTTP web server above.

Happy sharing!!!!


_________________
Image
Image
Image

CLINE SD,HD,4K SERVICE+PANAL
hd.kingsat.top
cn.smartcam.fun
gta.uhdcs.pw
hd.chongpang.pro
cs.gshare.club
CALL : 0301 833 1640
WHATSAAP : 03018331640
SKYPE : abaskhan378


Top
 Profile  
 
PostPosted: May 17th, 2018, 8:28 am 
Offline
-=SUPER MODERATOR=-
-=SUPER MODERATOR=-
User avatar

Joined: April 24th, 2016, 7:45 pm
Posts: 1467
Location: -=PUNJAB=-
Has thanked: 390 times
Been thanked: 1868 times

aur agay lines kaise create kerni hai yeh bhi to likhain abbas bhai


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC + 5 hours


Related topics
 Topics   Author   Replies   Views   Last post 
There are no new unread posts for this topic. how to install any iptv app on your pc

zagallo

0

111

October 10th, 2017, 4:54 pm

zagallo View the latest post

There are no new unread posts for this topic. plz guide me

aquagreen

12

1929

September 21st, 2015, 9:10 am

Shoukat Bagrani View the latest post

There are no new unread posts for this topic. spark new software 1.2.83 usb install

jamalnasir4242

8

1016

March 14th, 2016, 6:47 am

Rizwanjee233 View the latest post

There are no new unread posts for this topic. Install Power Vu Autoroll

ali03000345

0

436

May 9th, 2017, 2:41 pm

ali03000345 View the latest post

There are no new unread posts for this topic. Automated install for OScam

ABBAS 786

3

689

December 17th, 2015, 12:35 pm

laxmandis View the latest post

 


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list
Powered by phpBB® Forum Software © phpBB Group

phpBB SEO